可靠性强化试验技术在某型伺服作动器研制中的适用性探索

目的探索可靠性强化试验技术在典型机电液一体化产品伺服作动器研制过程中的适用性。方法以某型伺服作动器为研究对象,从故障激发的角度对可靠性强化试验技术的应用进行可行性分析,在响应调查和应力分析的基础上,结合产品的工作特点设计适用于该类伺服作动器的可靠性强化试验方案,包含低温步进应力试验、高温步进应力试验、快速温度循环试验10个循环、振动步进应力试验(包含气锤式三轴向六自由度超高斯随机振动方式及电磁振动台随机振动方式)及综合环境应力试验5个循环,并依此进行试验。结果在快速温度循环试验及综合环境应力试验过程中,均有效地激发出了产品的漏油故障,与相似产品外场暴露的漏油故障模式相吻合。结论可靠性强化试验技术可有效地应用于典型机电液一体化产品伺服作动器的研制过程,设计的可靠性强化试验方案可有效地激发外场出现频率较高的故障,可作为该类产品研制的试验手段之一。     

空间站控制力矩陀螺微振动测试技术

目的分析控制力矩陀螺的微振动扰动特性。方法通过获取陀螺连接点对结构的扰振力输出、关键部位的微振动响应来获取产品的微振动扰动特性,通过隔振的方式对外部环境的干扰进行隔离,进而降低测试的背景噪声,通过运用高精度测试传感器来实现微小扰动力信号、加速度信号的测量,利用结构有限元法及单点激励多点响应的模态分析方法校核系统刚度,进而确定测试频率范围是否满足需求。结果可同时获得空间站控制力矩陀螺连接点处的输出扰振力、质心处的输出扰振力合力、合力矩以及关键部位的微振动响应,可有效隔离外部干扰,扰振力背景噪声的时域信号最大值可控制在0.07 N以内,RMS值在0.02 N以内,加速度信号的时域背景噪声最大值可控制在1.5 mg以内,RMS值在0.1 mg以内。可识别微小扰振信号,加速度传感器分辨率为5×10-5 grms,力传感器的测量分辨率为1×10-2 N,力矩测量分辨率小于1×10-2 N·m。测试频带在320 Hz以内。结论满足型号需求,并投入型号使用。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

长输管道泄漏检测技术进展浅析

简述了长输管道泄漏检测技术的进展情况,介绍了4种泄漏检测技术原理,并对比分析了各种技术的特点和应用范围,为管道的安全运行管理和维护决策提供了技术参考。     

电子产品虚拟试验评估技术综述

介绍了虚拟试验技术在电子产品评估鉴定中的应用方法。首先论述了虚拟试验技术产生的背景及其技术优势。然后结合国外的研究状况,重点对电子产品虚拟试验评估技术的基本流程和涉及的关键技术作了总结和归纳。最后,指出虚拟试验技术在电子产品评估中具有广阔的应用前景。     

Evaluation of mercury speciation and removal through air pollution control devices of a 190 MW boiler

Air pollution control devices (APCDs) are installed at coal-fired power plants for air pollutant regulation. Selective catalytic reduction (SCR) and wet flue gas desulfurization (FGD) systems have the co-benefits of air pollutant and mercury removal. Configuration and operational conditions of APCDs and mercury speciation a ect mercury removal e ciently at coal-fired utilities. The Ontario Hydro Method (OHM) recommended by the U.S. Environmental Protection Agency (EPA) was used to determine mercury speciation simultaneously at five sampling locations through SCR-ESP-FGD at a 190 MW unit. Chlorine in coal had been suggested as a factor a ecting the mercury speciation in flue gas; and low-chlorine coal was purported to produce less oxidized mercury (Hg2+) and more elemental mercury (Hg0) at the SCR inlet compared to higher chlorine coal. SCR could oxidize elemental mercury into oxidized mercury when SCR was in service, and oxidation e ciency reached 71.0%. Therefore, oxidized mercury removal e ciency was enhanced through a wet FGD system. In the non-ozone season, about 89.5%–96.8% of oxidized mercury was controlled, but only 54.9%–68.8% of the total mercury was captured through wet FGD. Oxidized mercury removal e ciency was 95.9%–98.0%, and there was a big di erence in the total mercury removal e ciencies from 78.0% to 90.2% in the ozone season. Mercury mass balance was evaluated to validate reliability of OHM testing data, and the ratio of mercury input in the coal to mercury output at the stack was from 0.84 to 1.08.     

水质氨氮在线监测仪发展现状

水中氨氮作为"十二五"国家重点控制污染指标,其在线监测设备的发展至关重要,本文主要介绍了目前中国市场上存在的主要水质氨氮在线监测仪的原理情况,并按照国家标准对其进行基本性能和实际水样测试的比较试验,为水质氨氮在线监测仪的应用提供参考。     

Development of a biaxial loading frame for sheet metal

Characterization of the evolving yield loci and forming limit diagrams for sheet materials under biaxial loading is necessary for the development of accurate sheet metal forming process simulations. Biaxial tension testing has been shown to have significant advantages over the current computational and experimental methods for such material characterization; however, the few commercially available loading frames are far too large and expensive to be practical for most metal forming research laboratories. In this paper, the design of a practical servohydraulic biaxial loading frame is presented. The design, control, and operation of the loading frame are discussed in detail, and experimental data is provided to validate the effectiveness of the control system with respect to specimen center shifting.     

Current status and trends of the environmental performance in European ports

This paper investigates the current status and trends over time in the environmental performance of European ports. The research is based on the provision of data from 79 European ports on issues related to their environmental management, environmental priorities and current environmental monitoring practices. This study updates previous environmental reviews, so that the trends over time are drawn. For instance, 90% of respondent ports stated that they have an environmental policy and 94% of ports have designated environmental personnel. The percentage of ports that have an Environmental Management System has increased by +33% in the last 9 years. Air quality, port waste and energy consumption emerged as the three major environmental priorities of the European port sector in 2013. The research also reveals the diversity amongst European ports in terms of size and physical surroundings. Some examples are presented on specific initiatives carried out by sector organisations about the Top-10 port priority issues. The future expectations of European ports on data collection and reporting are described.